Hp Storageworks 3000 Sas Driver
Push the server latch down to lock the tape drive into position, as shown in below figure. Tape compatibility » HP Data Agile BURA Compatibility Matrix » HP StoreEver Tape Library Drive Upgrade Matrix » Single Point of Connectivity Knowledge (SPOCK) Tape tools » HP Library and Tape Thank you! If the screws are too long, they may penetrate the mechanism and void the warranty. http://3podjobs.com/hp-ultrium/hp-storageworks-ultrium-3000-sas-driver.php
The information provided is provided "as is" without warranty of any kind. An unapproved power cord could fracture resulting in the internal contacts being exposed, which potentially could subject the user to a shock hazard. Connect SAS and power cords . For complete release notes, go to: http://bizsupport1.austin.hp.com/bc/docs/support/SupportManual/c03785044/c03785044.pdf DETAILS Installation instructions Use HP Library & Tape Tools (L&TT) to update the tape drive firmware. http://h20564.www2.hpe.com/hpsc/swd/public/readIndex?sp4ts.oid=4202052
Hp Ultrium 5-scsi Driver
Installing drivers after connecting the tape drive (Windows only) For the drivers which are not installed, the Windows Found New Hardware wizard will run when power ON the server and tape These are 3mm screws and have a thicker head than the General Mounting Screws. Insufficient conductor ampacity that could result in overheating with potential personal injury and/or property damage.
Have all the devices reconnected securely? Figure 6: Cabling to a new HBA (cable for LTO-5 drive shown) Item Description 1 Remove plastic cover and connect SAS cable to new HBA 2 New SAS HBA 3 SAS Select your product and operating system. Hp Ultrium 5-scsi Firmware Ultrium 3000 tape drives: Connect a spare power cable from the server's internal power supply to the power connector on the SAS data cable.
top Installing an external LTO Ultrium tape drive This chapter describes how to connect the tape drive to an external port on the host controller or new HBA. Hp Ultrium 5-scsi Driver Windows 2012 Server manuals (for reference during installation). Ultrium 3000 tape drives: Connect a spare power cable from the server's internal power supply to the power connector on the SAS data cable. http://h20564.www2.hpe.com/hpsc/doc/public/display?docId=emr_na-c05156494&sp4ts.oid=4150338 Phillips screwdriver (server using Phillips screws).
Hp Ultrium 5-scsi Driver Windows 2012
Remove the plastic cover from the Mini SAS connector and connect the SAS cable supplied with the tape drive to the new HBA. http://h20564.www2.hpe.com/hpsc/doc/public/display?docId=emr_na-c03813560 Guidelines Log In Please log in to CNET to comment Post Comment As... Hp Ultrium 5-scsi Driver Torx screwdriver (server using torx screws). Hp Storeever Lto-5 Ultrium 3000 Sas External Tape Drive Coil and secure the unused cabling so that it does not interfere with other components inside the server.
Provide feedback Please rate the information on this page to help us improve our content. have a peek at these guys These are shoulder screws and have a thick offset piece and a thicker head than the General Mounting Screws. If the server or enclosure rails are less than 1.5 mm thick, use the washers from the General Mounting Screws screw pack for a proper fit. Remove the plastic covers from both connectors on the supplied Mini SAS cable. Hp Lto 5 Ultrium 3000 Driver
NOTE: This option is not recommended for Gen8 or Gen9 servers because the use of all four hard drive bays can be lost. Windows Backup or UNIX native backup applications can be used to check basic tape drive operation, but they will not support all the advanced features of the tape drive. Server that does not use mounting hardware, verify that the holes in the chassis are aligned with the holes in the side of the tape drive. http://3podjobs.com/hp-ultrium/hp-storageworks-ultrium-3000-drivers.php Sign-in Register Site help Skip to ContentSkip to FooterSolutionsHybrid IT with CloudMobile & IoTIT for Data & AnalyticsPublic SectorService ProvidersSmall & Midsize BusinessFinancial ServicesHealth & Life SciencesManufacturingTelecommunications All Solutions ServicesAdvisory and
Figure 9: Cabling to the spare SAS port (some HP ProLiant servers, cable for LTO-5 drive shown) Item Description 1 Connect SAS cable to spare SAS port (remove cover on Mini Hp Storeever Tape Drivers For Windows If there are any error or unexpected messages go back and check the SAS cabling carefully. Always use a spare power cord from the server's internal power supply.
Never use this option with RAID configurations.
Carry out a backup and restore test to check that the drive can write data to tape. Watch the boot screen carefully after installation. Figure 13: Cable routing with replacement SAS cable Item Description 1 Replacement SAS cable 2 Connect replacement SAS cable to host SAS HBA 3 Power connector to server (Ultrium 3000 only) Hp Ultrium 6-scsi Scsi Sequential Device Driver The rails may be attached to the filler panel by screws of a different thread/size type and these should not be used.
If the Windows Found New Hardware wizard runs, cancel it - user can use Device Manager to check that the driver is installed. For current information about SAS host controllers and cabling options with HP ProLiant servers, see the data agile BURA compatibility matrix website at: Click here to view the Data Agile BURA Remove the plastic cover from the Mini SAS connector connect the SAS cable supplied with the tape drive to the spare SAS port on the host SAS controller. http://3podjobs.com/hp-ultrium/hp-ultrium-3000-sas-drivers.php Doing so could leave the product in a nonusable state.
Mounting screws Other HP ProLiant server models, such as ML350 and ML370, only require the use of special locating screws with no mounting rail. Locate both screws lightly in position before tightening, as shown in below figure: HP ProLiant ML350: Use the metal shims and screw pack labeled ProLiant ML350. There is a separate power connector on the rear of the tape drive. The only way to be sure, is to check the disk LEDs after installating the tape drive.
This caution does not apply to Ultrium 3000 tape drives. A suitable cable is supplied with the tape drive for connecting to an external Mini SAS port. Connect to a dedicated HBA (recommended) Connect to a spare port on the host controller (recommended) If both ports on the host controller are in use, replace one of the existing Was the information on this page helpful?
This cabling option is described as Option 3 . The second branch of the split cable is not required for this installation. If user have lost the use of a disk bay, It has been strongly recommend that one should attach the supplied sticker to the blanking plate of the disk bay to Always use a spare power cord from the server's internal power supply.
Figure 18: SAS cable supplied with the external tape drive Item Description 1 High density Mini SAS connector for the server 2 Mini SAS connector for the tape drive If the This is a split cable, but the second branch is not required.nt