Hp Smart Array 6i Drivers
Disabled a function designed to detect a condition where a SCSI disk drive unexpectedly changes its SCSI ID. This function was previously part of the FW for the SA-6400, SA-641 and Enhancements 1. RAID Support RAID 5 (Distributed Data Guarding) RAID 1+0 (Striping and Mirroring) RAID 1 (Mirroring) RAID 0 (Stripping) Disk Drive and Enclosure Protocol Support Ultra320, Ultra3, Ultra2 Sponsored Products Category Category Drivers Subcategory SCSI Drivers Publisher's Description+ From HP: Smart Array 6i: The new Smart Array 6i controller is an Ultra320 intelligent array controller for entry-level, hardware-based fault weblink
Drive Mirroring (RAID 1, 1+0): This allocates half of the drive array to data and the other half to mirrored data, providing two copies of every file. How to select driver? Please help us to make SME Server a better product. Using last good known configuration fixes it.
The information contained herein is subject to change without notice. Fixed an issue that causes the HP Insight Management Agents to display incorrect characters for the DL360 G4.3. Software Suite All Smart Array products share a common set of configuration, management and diagnostic tools, including Array Configuration Utility XE (ACU-XE), Array Configuration Utility (ACU), Array Diagnostic Utility (ADU), and
HP ProLiant DL380 G4 Packaged Cluster with MSA500 G2 HP ProLiant DL385 (SCSI models only) HP ProLiant DL580 G3 HP ProLiant BL20p G3 HP ProLiant BL25p HP ProLiant BL45p NOTE: For It is recommended for up to 14 hard drives. Fixed a bus fault issue on dual bus I/O modules. Models Smart Array 6i Controller Smart Array 6i Controller NOTE: The Smart Array 6i Controller ships integrated on the HP ProLiant DL360 G4, HP ProLiant DL360 G4p (SCSI models only), HP
Enhancements Improved cache flushing and performance. A new version of firmware can be flashed to the ROM while the controller maintains the last known working version of firmware. The DL380 G4 has a second channel for optional duplex backplane support or external tape support. Enhancements 1.
I attempted the instructions from the hp site but got 'error: Failed dependencies: .....' message.Any help and guidance would be much appreciated.ThanksAyaz Logged Stefano Site Administrator Offline Posts: 10,445 Skype account: This helps prevent battery status messages from alternating or indicating false status.Updated the battery firmware to reduce the chances of deep discharging the battery. Fixed Array behavior to prevent unwanted device migrations by detecting conditions, where a SCSI disk drive unexpectedly changes its SCSI ID. 3. Can you help with a gui that will help me to convert the 4 drives to raid 5 or the commands via command line.Thanksyou can't change anything nowreinstall SME with only
Added support for the controller firmware to place a Monitoring and Performance stamp (M&P) on the disk drive, if it is missing from the drive.2. have a peek at these guys Fixed an issue where inquiries to the logical drive would succeed even after the drive is physically removed. Logged mak999 Just popping in Offline Posts: 3 Re: Instructions on Installing drivers for smart array 6i on hp dl380 g4 « Reply #3 on: September 30, 2011, 07:03:30 PM » Fixed an issue where inquiries to the logical drive would succeed even after the drive is physically removed.
Fixed an issue with the component installer that may cause this component to not be recognized under the Windows Preinstallation Environment (Windows PE). Thank You for Submitting Your Review, ! If the firmware becomes corrupt, the controller will revert back to the previous version of firmware and continue operating. check over here I have installed SME server 8 beta release 6, performed all updates and installed 3ware 3dm2.
thank you Logged Consulente di Smeserver.it - Soluzioni e supporto su Sme server in Italia mak999 Just popping in Offline Posts: 3 Re: Instructions on Installing drivers for smart array 6i Watch this video to see how it works - click here *: 2K=Windows 2000, 2K3= Windows 2003 , XP= Windows XP , VISTA = Windows Vista , WIN7 = Windows 7,WIN10= If you are looking for an update , pickup the latest one.
This also reduces the time required for a battery recharge cycle to complete.Updated the battery firmware to improve the sensing and reporting of battery health.
On-Line Spares: Up to two spare drives can be assigned prior to drive failure. NOTE: On-Line Spares can only be used with RAID level 1, 1+0, and 5. This software consistency of tools reduces the cost of training for each successive generation of product and takes much of the guesswork out of troubleshooting field problems. Provide feedback Please rate the information on this page to help us improve our content.
All rights reserved. Enhanced performance for drive rebuilds and RAID 5 and RAID 6 (ADG) configurations.5. Fixed an issue where Windows Server x64 would hang or blue screen when the Smart Array driver is installed or upgraded on a system that has greater than 7GB RAM. 2. http://3podjobs.com/hp-smart/hp-smart-array-5i-drivers.php Updated recommended hard drive firmware list with models that have been experiencing excessive SCSI command timeouts. When one of these drives is present, user will see a POST message recommending he upgrade
To avoid notification during the POST routine, update any applicable hard disk drives before updating the Smart Array firmware. You are logged in as . This POST message will now display if this condition has occurred when no logical volumes are present or if cache has already been disabled. Version:2.80(A) (25 Sep 2007) Fixes Upgrade Requirement:Recommended - HPE recommends users update to this version at their earliest convenience.
Release Notes End User License Agreements: Hewlett-Packard End User License Agreement Important: The firmware update Version 2.48 contains critical bug fixes and is the minimum version required. Please perform the update Was the information on this page helpful? how does SME sees the hds?)so you don't need anything moreI guess you are looking for monitoring tools.. Updated POST message 1794 "Array Accelerator batteries have failed to charge and should be replaced".
Logged CharlieBrady Development Team Offline Posts: 6,882 Re: Instructions on Installing drivers for smart array 6i on hp dl380 g4 « Reply #6 on: September 30, 2011, 08:25:08 PM » Quote For more details, refer to Customer Advisory EM041123_CW01 Version:2.34 (A) (17 Dec 2004) Fixes Fixed an issue where the battery status may be falsely reported as “failed” even though the cache module The Smart Array Advantage HP's innovative design and integration work of the Smart Array family of products creates customer value that is unmatched in the industry. If you have previously upgraded to version 2.58 firmware another update is not needed.2.
Please submit your review for Smart Array 6i 1. Select driver language and OS Driver language Chinese (Simplified) Chinese (Traditional) English French German Italian Japanese Korean Spanish Operating systems in English Select your product's operating system Microsoft Windows 2000 Microsoft Changed the SCSI ID detection algorithm for SCSI disk drive that unexpectedly changes its SCSI ID, in configurations involving duplex backplanes. Pre-Failure Warranty Means Insight Manager not only reports when a drive is going to fail but also allows replacement of failing drives prior to actual failure.
Version:2.80(A) (25 Sep 2007) Fixes Upgrade Requirement:Recommended - HPE recommends users update to this version at their earliest convenience. Added support for the 512MB Battery-Backed Write Cache (BBWC) option.6. Enhancements Improved cache flushing and performance. Trying to replace the 2012 driver from Microsoft with the Windows x64 HP-driver (from 2008, probably made for Windows Server 2008) only leads to the server crashing at boot.nt