conteHome > Hp Smart > Hp Smart Array 5i Plus Controller Driver

Hp Smart Array 5i Plus Controller Driver

The flowcharts in Figure 2-1 and Figure 2-2 summarize the installation procedures for the most common scenarios. Creating a Custom Configuration for a New Array 1. A5. This technique improves system performance. weblink

Page 128 Glossary CPQONLIN An array configuration utility for Novell NetWare that can be used while the server is online. Note: You can not upgrade from the Integrated Smart Array Controller to the Smart Array 5i Controller because the Integrated Smart Array Controller is embedded on the system board and can What is the difference between the Smart Array 5i and the Smart Array 5i Plus? Page 83 Drive Arrays and Fault Tolerance With an array controller installed in the system, the capacity of several physical drives can be combined into one or more virtual units called

NT 4.0 Server NT 4.0 Enterprise Edition NT 4.0 Terminal Server Windows 2000 Windows 2000 Advanced Server NetWare 4.2* NetWare 5.x Linux Redhat 7.0, 7.1 Caldera OpenLinux 2.3.1 and 3.1 UnixWare Page 23 Updating the System Firmware Before installing an array controller in a Compaq server, update the system firmware by running the System ROMPaq utility. A13.

Page 37 Configuring an Array Using ORCA When a computer system is powered up, part of the startup sequence is the Power-On Self-Test (POST). Page 139 Index Taiwanese A-6 SCSI replacing hard drives bus termination D-1 general information D-7 devices, compatibility of 1-5 precautions for D-9 Low Voltage Differential Signaling reprogramming (LVDS) 1-5 options ROM Page 135 Index error messages F-1 fast-charging, Battery Backed Write Cache ESD (electrostatic discharge) Enabler 1-4 obtaining additional information B-2 fault management features precautions B-1 automatic data recovery D-6 preventing B-1 Conforms to the Wide-Ultra SCSI standard.

For complete details, consult the Compaq Support Center or refer to your Compaq Server documentation. Page 60: Using Cpqonlin Configuring an Array 3. When any other physical drive in the array fails, the controller automatically rebuilds information that was originally on the failed drive onto the online spare. When the batteries are fully battery charge low.

Page 133 Index features 1-1 status lights of 1-3 installation description 3-1 trickle-charging 1-4 installation process 2-1 battery module See Battery Backed Write interface 1-5 Cache Enabler memory 1-4 block of What is the primary problem solved by Recovery ROM? 15. The Compaq Smart Array family brings an unparalleled return on investment through: Data Compatibility - among all models of Smart Array controllers allows simple and easy upgrades any time needs for Alter the settings on this screen to suit your needs. 4.

Now being phased out in favor of LVD technology. Page 112 POST Error Messages Table F-1: POST Error Messages continued Message Description Meaning and Recommended Action 1764 Slot x drive array – The capacity expansion process has been capacity expansion Each drive on a SCSI bus must have a unique ID value in the range 0 to 15 (except ID 7, which is reserved for controller use). Page 55 Configuring an Array Figure 7-17: Example array – Logical Configuration View window, two arrays NOTE: The capacity shown for each logical drive is the free capacity available for data

Table F-1: POST Error Messages Message Description Meaning and Recommended Action... have a peek at these guys Warranty status: Unspecified Check warranty status Drivers & software Help Knowledge base options Search HPE Support Center - HPE Most viewed solutions Advisories, bulletins & notices Manuals Troubleshoot a problem Learn & End of content United StatesHewlett Packard Enterprise International Start of Country Selector content Select Your Country/Region and Language Click or use the tab key to select your country ArgentinaAustraliaBelgiqueBoliviaBrasilCanadaCanada-françaisChileColombiaDeutschlandEcuadorEspañaFranceIndiaIrelandItaliaMéxicoNederlandNew ZealandÖsterreichParaguayPerúPolskaPortugalPuerto RicoSchweizSouth A17.

Figure 6-1: RBSU menu screen 3. These tools lower the total cost of ownership by reducing training and technical expertise necessary to install and maintain the Compaq server storage. However, there is an increased risk that data will be lost if another physical drive fails while the rebuild is in progress. check over here Privacy Policy Welcome to Do you know that DriverIdentifier can help you finding driver in just a few minutes?

Page 16: Controller Interface, Scsi Support, Drive Array Technology Features Controller Interface The Smart Array 5i Plus Controller and Battery Backed Write Cache Enabler interfaces to the server through a high-performance This label appears on a laser device installed in your product. Updates are posted to the Compaq website,

The ads help us provide this software and web site to you for free.

If your controller has a battery backed write cache, check the Controller Settings screen to confirm that the write cache is enabled. 4. Click here to check warranty status . NOTE: Raw logical drives are invisible to the operating system. Page 27: Running Options Rompaq From The Smart Array Controller Support Software Cd Updating the Controller Firmware Running Options ROMPaq from the Smart Array Controller Support Software CD 1.

Will the Smart Array 5i support both internal and external drives at the same time? Turn off system and check cable cables or replace the connections. Get the perfect match for your driver More than 5 million happy users Install using DriverMax Only download this driver VPN PRO Advanced Uninstaller PRO Orange Defender NeoSetup Home Download Purchase Detailed information about these messages is given in Table F-1.

What configuration utilities and management utilities are needed for the Smart Array 5i? Where does the Smart Array 5i Controller fit in the Compaq family of array controllers? The default boot size is 32 sectors (16 kbytes) per track, and the maximum boot size is 63 sectors per track. vii Symbols in Text.......................viii Text Conventions.......................

This message appears resuming logical drive whenever a controller reset or power cycle occurs expansion process. All other Smart Array controllers are connected through a PCI slot. Running System ROMPaq from Diskette To run System ROMPaq from diskette, you must first create a System ROMPaq diskette from the CD or from the appropriate SoftPaq file.